29
Jan
Replace the PSP analog stick. Eh this is my first tutorial on how to change your broken psp fat analog stickDont forget to comment and subscribe for more tutorials.
Remove the 5 screws 4 black screws 1 silver screw on the side that hold the PSP faceplate on.
Psp analog stick replacement. Now you can carefully separate the two halves of the PSP. Also remove the top of the analog stick when performing this step. It will come of just by pulling it.
Replace the PSP analog stick. Now you have a PSP in two halves. The analog stick is attached with 2x silver screws as seen in the image below.
To replace it simply remove the screws add your replacement from eBay and attach. Place the PSP face down and locate the battery cover on the left side of the device. Lift and remove the battery cover to reveal the battery.
Use your wirecutter to snip a few milimetres off the end of the tack so that it will fit snugly into your PSP while not sticking too far out. Add Tip Ask Question Comment Download Step 4. Anyone who has played N64 or GameCube knows how bad a limp analog stick can suck.
Replace your PSP 300xc and never settle for loose sticks again. Phillips 00 Screwdriver. Sony PSP 3000 Analog Stick.
With the PSPs faceplate removed position the PSP so that the analogue stick is easily attainable. Gently pull up on the analogue stick. It should just pop off from the rest of the device.
In order to clean it correctly take a cotton swab w rubbing alcohol and clean the base of the analogue stick. How to repair the PSP-3000 stick does not work does not respond etc and how to disassemble it. PSP-3000 Analog Stick Replacement and Decomposition Procedure Analog stick exchange and decomposition method step 1 of PSP-3000 Start from the place where you can open the cover in the left part of the image.
3D Analog Joystick Thumb Stick Replacement For Sony PSP 1000 Console Controller. 4pcs Black Analog Joy Stick Joystick Cap Cover Button For Sony PSP 1000 1001 New. You have to open up your psp and take out the analog stick by taking out a couple of screws then you must take a qtip and dip it in alchohol rubbbing at least 70 percent iso then clean the analog and rubber conductor as well and remeber to place the rubber conductor bac at the same place if you replaced your housing that may be the problem as to why it may not work and you may want to replace.
I fixed this prob in my psp by taking out the small clear rubber connector between thE analog stick and the pcb and cleaning it with a damp cloth then drying it and putting it back in. Be sure to put it back in correctly NOW THE ANALOG STICK IS WORKING PERFECTLY - PSP 1000 Buttons Replacement This guide should show you how to do it. You might only have to follow up to the end of.
Use a plastic opening tool around the perimeter of the back cover to loosen it on all sides. Open the back cover by gently lifting the right side and rotating it to the left side as if you were opening a book. Be careful not to rotate the back cover from the bottom as you will break the plastic screw holes on top of the device.
Sadly i couldnt find any drop-in replacements but the PSP sticks are very close. All i had to do was dremel away a little bit on the sides of the hole on the PSP analog sticks. Modified PSP Stick on the left original stick in the middle and an unmodified PSP stick on the right for comparison.
2X Analog Stick Black Replacement Compatible with Sony Playstation Portable PSP 1000 Series. 50 out of 5 stars. Get it as soon as Wed Oct.
CONFIRMED TO WORK ON REGULAR SIZED NEW 3DS. MUST BE A PSP 1000 ANALOG CAP NOT 20003000 Edit 7. People were concerned that this wasnt easily reversible heres my solution.
Cut the excess rubber pieces off and then press the original C-stick back into place. Use a paper clip or sturdy blunt tip to stuff the edges back into place. For PSP 2000 3000 Series - Replacement Analog Thumb Button Joy Stick Cap FPC 240 PSP Analog Joystick 3D Control Stick PSP 2000 2XXXX Black - UK Dispatch.
10pcs 3d Analog Joystick Thumb Arcade Stick For Psp Joystick Potentiometer Switch Console Controller Repair Lazada Singapore Psp Thumb Stick Mod With Psvita. PSP 3000 Disassembly and Analog Stick Replacemen Tutorial - YouTube. PSP 3000 Disassembly and Analog Stick Replacemen Tutorial.
Go to system setting in the menu of your PSP and then go to system information. While on the system information screen start turning the analog stick in a clockward motion over and over REALLY FAST. At the very least you need to turn it perfectly 20 times but do.
Eh this is my first tutorial on how to change your broken psp fat analog stickDont forget to comment and subscribe for more tutorials. Qisuw 3D Analog Joystick Thumb Stick Replacement For Sony PSP 3000 Console Controller. 100 brand new and high quality.
Left controller thumb joystick analog sensor gamepad stick with cap. For Sony PSP 3000. Use for replace the original old and damaged parts makes it looks new all the time.
This guide will explain to you how to replace the analog joystick on your PSP 3000. Analog joystick no longer functions well or doesnt respond at all Some advice before you start. Grab and pull the analog stick very gently.
Dont remove the analog stick just yet. It is still attached to the logic board by a cable. Remove the 5 screws 4 black screws 1 silver screw on the side that hold the PSP faceplate on.
You can find videos of this on youtube or other instructables. Flip the faceplate over and remove the two silver screws that retain the. 3D Analog Joystick Stick Button Sensor Module for PSP 2000 PSP 2000 PSP-2000 Replacement.
3D analog joystick for P-S-P 2000 Repair your old and malfunctioning parts by replacing with high quality replacement parts Perfect replacement for your worn out 3D joystick for P-S-P 2000 Third party product Color. Black 1pcs Joysticks more.